Fly Buffer Plus Firmware Flashing

Applicable Versions

This document applies to devices with firmware versions lower than v2.0.0. If your firmware version has reached or exceeded this version, please refer to the Firmware Update document and update directly via the web tool without entering DFU mode.

Check Firmware Version

Through the Web Tool, you can view the current firmware version number after connecting the device.

Enter DFU Flashing Mode

Power Off

Before starting, fully shut down the printer and disconnect the power supply. Do not plug or unplug cables, organize wiring, or touch terminals while the device is powered on.

You can put the device into flashing mode using any of the following methods:

• Method 1:

  1. Connect the device to your computer using a Type-C data cable.
  2. Press and hold the BOOT button on the device, briefly press the RESET button, then release BOOT.

• Method 2:

  1. Press and hold the BOOT button on the device.
  2. Connect the Type-C data cable to both the device and the computer, then release the BOOT button.

Loading...

Flashing Methods

• WIN Flashing
• Linux Flashing
• FLYOS Flashing

• FLY-LLL-PLUS-V2.0.1-mergedBL.bin

Windows 默认可能隐藏文件扩展名。下载后请确认文件扩展名未被修改，不要保存成 .txt 或其他扩展名。

• STM32CubeProgrammer
• APM32 DFUProgrammer
• DFU-AUTO

Notice

To ensure successful STM32 flashing, please note the following:

• The USB port on some computers may cause unstable flashing due to driver or signal compatibility issues. It is recommended to try a different USB port for connection.
• If changing ports does not work, an effective solution is to connect via an external USB hub, which often improves compatibility.
• When the flashing software reports the error shown below, please also prioritize trying a USB hub. If the issue persists, check or use the host computer for flashing.
  Loading...

1. Flashing tool Download Link
2. You need to download SetupSTM32CubeProgrammer and STM32 DFU Driver
3. Download the firmware to any directory on your computer
4. Connect the motherboard to the computer using a Type-C cable, ensuring it has entered dfu flashing mode
5. In STM32CubeProgrammer, select USB mode, refresh, and connect
   Loading...
6. If no error popup appears, the connection is successful.
   Loading...
7. Click the download icon on the left and check the following options
   Loading...
8. Click Browse as indicated by the arrow, then select the firmware you need to flash
   Loading...
9. Set Start address to 0x08000000
   • Note: If the firmware is in HEX format, please skip this step!!
   Loading...
10. Click Start automatic mode below to begin flashing the firmware
    Loading...
11. The following prompt indicates that the firmware flashing is complete
    Loading...

1. Download the flashing tool: Download Link
2. Install the DFU driver: Download and extract DFUProgrammer. The package includes the DFU driver for APM32. Please install this driver manually.
3. Prepare the firmware: Copy the previously compiled firmware file to any directory on your computer (e.g., the desktop) for easy selection later.
4. Enter DFU mode: Connect the mainboard to the computer using a Type-C cable. Ensure the mainboard is in DFU flashing mode (usually set via a jumper cap; for specific methods, refer to the mainboard's DFU entry instructions).
5. Run the flashing tool: Open DFUProgrammer and select and configure as shown in the images below:
   Loading...
   Loading...
6. Start flashing: Click the "Start Updating Firmware" button and wait for the progress bar to complete. Once the flashing is successful, you can disconnect the Type-C cable and remove the jumper cap.

1. Download and run FLY DFU-AUTO
2. If the Driver Status is unavailable, click Install Driver to complete the WinUSB driver installation
3. Click Browse... and select the .bin firmware file to be flashed
4. Click Start Flashing, view the flashing progress via the Running Log below, and wait for the flashing to complete

Detailed Tutorial: FLY DFU-AUTO Download and Usage

1. Install flashing tool.

   sudo apt update
   sudo apt install dfu-util -y

2. Confirm the device has entered DFU flashing mode.

   lsusb

   If you can see 0483:df11, it means DFU flashing mode has been entered successfully.

   Loading...
3. Pull/update firmware repository.

   git clone https://cnb.cool/3dmellow/FLY-Firmware ~/FLY-Firmware
   cd ~/FLY-Firmware && git pull --ff-only

4. Flash firmware.

   sudo dfu-util -a 0 -d 0483:df11 --dfuse-address 0x08000000 -D ~/FLY-Firmware/ExtensionBoard/LLL-PLUS/mergedBL/FLY-LLL-PLUS-V2.0.1-mergedBL.bin

5. If File downloaded successfully appears, flashing is successful.
   Loading...

1. FLY host computer usually has dfu-util built-in, no need to install flashing tool again.
2. Confirm the device has entered DFU flashing mode.

   lsusb

   If you can see 0483:df11, it means DFU flashing mode has been entered successfully.

   Loading...
3. Pull/update firmware repository.

   git clone https://cnb.cool/3dmellow/FLY-Firmware /data/FLY-Firmware
   ln -s /data/FLY-Firmware /root/FLY-Firmware
   cd /data/FLY-Firmware && git pull --ff-only

4. Flash firmware.

   sudo dfu-util -a 0 -d 0483:df11 --dfuse-address 0x08000000 -D /data/FLY-Firmware/ExtensionBoard/LLL-PLUS/mergedBL/FLY-LLL-PLUS-V2.0.1-mergedBL.bin

5. If File downloaded successfully appears, flashing is successful.
   Loading...

Note

Do not disconnect the Type-C connection during the flashing process, as this may cause the flashing to fail.

Next Steps

After the BOOT firmware flashing is completed, the device supports direct main firmware updates through the web tool without needing to enter DFU mode again.

Please refer to the Firmware Update document to complete the main firmware update.