Skip to main content

Pinout

Note
  • This page lists the pinout of the FLY-C8P motherboard after flashing Klipper firmware. Pin numbers are based on the motherboard schematic.
  • UART/CS is the driver communication pin: used as UART when using TMC2209, and as chip select CS when using SPI drivers such as TMC5160. The same pin is multiplexed.
  • EN is the enable pin. In Klipper configuration, it is typically active-low (with ! prefix in enable_pin).
  • DIAG is the driver diagnostic signal pin. When using sensorless homing, configure the corresponding diag_pin according to the table below.
Loading...

Interactive Pin Hotspots​

This chart uses the FLY-C8P product image and hotspot data from the Klipper configuration generator. Use the device filters above to show only compatible connectors. Click a hotspot to see what it can connect to, common Klipper config sections, and wiring notes; use “Locate in pin table” in the detail panel to jump to and highlight the matching row below. Hover still shows the connector name and pin. Always verify the silkscreen and connector positions against the physical board and schematic.

Filter by deviceClick a device type to show only connectors that support it; click again to clear the filter.
FLY-C8PMotor driversHeatersThermistorsFansEndstopsRGBProbe / servo
FLY-C8P

Hover to see the pin; click a hotspot to view compatible devices and configs. Pins can be copied from the detail panel, except for driver connectors.

Driver Pins​

The FLY-C8P provides 8 driver ports:

DriverSTEPDIRENUART/CSDIAG
DRIVER0PE5PA8PA15PC9PD9
DRIVER1PE4PC11PC12PC10PD8
DRIVER2PE3PD1PD2PD0PD11
DRIVER3PE2PD4PD5PD3PD10
DRIVER4PE1PD7PB6PD6PA5
DRIVER5PE0PC13PC14PB7PA4
DRIVER6PE7PE11PE10PC15-
DRIVER7PE8PA7PA6PE9-
Power Off Before Operation

Before starting, completely shut down the printer and disconnect the power supply. Do not plug or unplug wiring harnesses, organize interface wiring, or touch terminals while the power is on.

DIAG and Sensorless Homing

In the table, rows where the Corresponding Driver DIAG is not - indicate that the driver's DIAG pin is connected to the corresponding input port on the main controller. When enabling sensorless homing, configure diag_pin directly according to the table. The corresponding input port will be occupied by the DIAG signal; do not connect mechanical or optical endstops to it simultaneously. The DIAG pins for DRIVER6 / DRIVER7 are not listed in the table.

SPI Bus​

SPI drivers such as the TMC5160 use the motherboard's hardware SPI bus. In the configuration, simply set spi_bus: spi1a. There is no need to configure MOSI/MISO/SCLK pins separately:

[tmc5160 stepper_x]
spi_bus: spi1a
cs_pin: Corresponding driver's UART/CS pin

Detailed instructions on software SPI and SPI speed, etc.: SPI Configuration Method

Endstops and Probe​

FunctionPinCorresponding Driver DIAG
Endstop Port 0 / IO0PD9DRIVER0
Endstop Port 1 / IO1PD8DRIVER1
Endstop Port 2 / IO2PD11DRIVER2
Endstop Port 3 / IO3PD10DRIVER3
Endstop Port 4 / IO4PA5DRIVER4
Endstop Port 5 / IO5PA4DRIVER5
ProbePC0-

For wiring of micro switches, optical endstops, proximity sensors, and TAP, see: Endstop Wiring Guide

Heaters​

FunctionPin
Heated Bed HeaterPB0
Heater Port 0PD12
Heater Port 1PD13
Heater Port 2PD14

Temperature Sensors​

FunctionPin
Heated Bed ThermistorPC5
Thermistor Port 0PC2
Thermistor Port 1PC3
Thermistor Port 2PC4
Supported Thermistor Types

The thermistor ports support NTC thermistors (100K) by default, with sensor_type recommended as Generic 3950; they also support 2-wire PT1000, configured by setting sensor_type to PT1000.

List of sensor_type options that can be directly connected internally by Klipper and their applicable scenarios: Thermistor Configuration Method

K-type thermocouples, 3-wire PT100, etc., require additional signal conditioning chips and cannot be connected directly to the thermistor ports.

Fans​

FunctionPin
Fan Port 0PA0
Fan Port 1PA1
Fan Port 2PA2
Fan Port 3PC6
Fan Port 4PC7
Fan Port 5PC8

PWM​

The FLY-C8P provides 3 PWM outputs, which can be used for servos, fan speed control, etc.:

PinNotes
PE6Servo / BLTouch Control
PA3RGB / Neopixel
PD15RGB / Neopixel

BL-Touch​

FunctionPin
Servo SignalPE6
Probe SignalPC0

RGB​

FunctionPin
RGB0 / NeopixelPA3
RGB1 / NeopixelPD15

EXP Interface​

EXP Configuration Reminder
  • The EXP header is commonly used for screens like the Mini12864 or other expansion peripherals.
  • If a pin is already used by SPI, UART, endstop, fan, or other functions, do not configure it again for EXP peripherals.

EXP1​

FunctionPin
EXP1_1PB10
EXP1_2PB1
EXP1_3PA14
EXP1_4PA13
EXP1_5PE15
EXP1_6PE14
EXP1_7PE13
EXP1_8PB11
EXP1_9GND
EXP1_105V

EXP2​

FunctionPin
EXP2_1PB14
EXP2_2PB13
EXP2_3PA9
EXP2_4PB12
EXP2_5PA10
EXP2_6PB15
EXP2_7PE12
EXP2_8RST
EXP2_9GND
EXP2_10NC
Loading...